Firmware of Anycubic 3D printer Vyper

Last update: Dec 27, 2022

Related tags

Overview

Marlin 3D Printer Firmware

Additional documentation can be found at the Marlin Home Page. Please test this firmware and let us know if it misbehaves in any way. Volunteers are standing by!

Marlin 2.0 Bugfix Branch

Not for production use. Use with caution!

Marlin 2.0 takes this popular RepRap firmware to the next level by adding support for much faster 32-bit and ARM-based boards while improving support for 8-bit AVR boards. Read about Marlin's decision to use a "Hardware Abstraction Layer" below.

This branch is for patches to the latest 2.0.x release version. Periodically this branch will form the basis for the next minor 2.0.x release.

Download earlier versions of Marlin on the Releases page.

Building Marlin 2.0

To build Marlin 2.0 you'll need Arduino IDE 1.8.8 or newer or PlatformIO. We've posted detailed instructions on Building Marlin with Arduino and Building Marlin with PlatformIO for ReArm (which applies well to other 32-bit boards).

Hardware Abstraction Layer (HAL)

Marlin 2.0 introduces a layer of abstraction so that all the existing high-level code can be built for 32-bit platforms while still retaining full 8-bit AVR compatibility. Retaining AVR compatibility and a single code-base is important to us, because we want to make sure that features and patches get as much testing and attention as possible, and that all platforms always benefit from the latest improvements.

Current HALs

AVR (8-bit)

board	processor	speed	flash	sram	logic	fpu
Arduino AVR	ATmega, ATTiny, etc.	16-20MHz	64-256k	2-16k	5V	no

DUE

boards	processor	speed	flash	sram	logic	fpu
Arduino Due, RAMPS-FD, etc.	SAM3X8E ARM-Cortex M3	84MHz	512k	64+32k	3.3V	no

ESP32

board	processor	speed	flash	sram	logic	fpu
ESP32	Tensilica Xtensa LX6	160-240MHz variants	---	---	3.3V	---

LPC1768 / LPC1769

boards	processor	speed	flash	sram	logic	fpu
Re-ARM	LPC1768 ARM-Cortex M3	100MHz	512k	32+16+16k	3.3-5V	no
MKS SBASE	LPC1768 ARM-Cortex M3	100MHz	512k	32+16+16k	3.3-5V	no
Selena Compact	LPC1768 ARM-Cortex M3	100MHz	512k	32+16+16k	3.3-5V	no
Azteeg X5 GT	LPC1769 ARM-Cortex M3	120MHz	512k	32+16+16k	3.3-5V	no
Smoothieboard	LPC1769 ARM-Cortex M3	120MHz	512k	64k	3.3-5V	no

SAMD51

boards	processor	speed	flash	sram	logic	fpu
Adafruit Grand Central M4	SAMD51P20A ARM-Cortex M4	120MHz	1M	256k	3.3V	yes

STM32F1

boards	processor	speed	flash	sram	logic	fpu
Arduino STM32	STM32F1 ARM-Cortex M3	72MHz	256-512k	48-64k	3.3V	no
Geeetech3D GTM32	STM32F1 ARM-Cortex M3	72MHz	256-512k	48-64k	3.3V	no

STM32F4

boards	processor	speed	flash	sram	logic	fpu
STEVAL-3DP001V1	STM32F401VE Arm-Cortex M4	84MHz	512k	64+32k	3.3-5V	yes

Teensy++ 2.0

boards	processor	speed	flash	sram	logic	fpu
Teensy++ 2.0	AT90USB1286	16MHz	128k	8k	5V	no

Teensy 3.1 / 3.2

boards	processor	speed	flash	sram	logic	fpu
Teensy 3.2	MK20DX256VLH7 ARM-Cortex M4	72MHz	256k	32k	3.3V-5V	yes

Teensy 3.5 / 3.6

boards	processor	speed	flash	sram	logic	fpu
Teensy 3.5	MK64FX512VMD12 ARM-Cortex M4	120MHz	512k	192k	3.3-5V	yes
Teensy 3.6	MK66FX1M0VMD18 ARM-Cortex M4	180MHz	1M	256k	3.3V	yes

Teensy 4.0 / 4.1

boards	processor	speed	flash	sram	logic	fpu
Teensy 4.0	IMXRT1062DVL6A ARM-Cortex M7	600MHz	1M	2M	3.3V	yes
Teensy 4.1	IMXRT1062DVJ6A ARM-Cortex M7	600MHz	1M	2M	3.3V	yes

Submitting Patches

Proposed patches should be submitted as a Pull Request against the (bugfix-2.0.x) branch.

This branch is for fixing bugs and integrating any new features for the duration of the Marlin 2.0.x life-cycle.
Follow the Coding Standards to gain points with the maintainers.
Please submit Feature Requests and Bug Reports to the Issue Queue. Support resources are also listed there.
Whenever you add new features, be sure to add tests to buildroot/tests and then run your tests locally, if possible.
- It's optional: Running all the tests on Windows might take a long time, and they will run anyway on GitHub.
- If you're running the tests on Linux (or on WSL with the code on a Linux volume) the speed is much faster.
- You can use make tests-all-local or make tests-single-local TEST_TARGET=....
- If you prefer Docker you can use make tests-all-local-docker or make tests-all-local-docker TEST_TARGET=....

RepRap.org Wiki Page

Credits

The current Marlin dev team consists of:

Scott Lahteine [@thinkyhead] - USA Donate / Flattr:
Roxanne Neufeld [@Roxy-3D] - USA
Chris Pepper [@p3p] - UK
Bob Kuhn [@Bob-the-Kuhn] - USA
João Brazio [@jbrazio] - Portugal
Erik van der Zalm [@ErikZalm] - Netherlands

License

Marlin is published under the GPL license because we believe in open development. The GPL comes with both rights and obligations. Whether you use Marlin firmware as the driver for your open or closed-source product, you must keep Marlin open, and you must provide your compatible Marlin source code to end users upon request. The most straightforward way to comply with the Marlin license is to make a fork of Marlin on Github, perform your modifications, and direct users to your modified fork.

While we can't prevent the use of this code in products (3D printers, CNC, etc.) that are closed source or crippled by a patent, we would prefer that you choose another firmware or, better yet, make your own.

Comments

I tried to compile the source and it fails saying the board type is wrong.

I am waiting for a strain gauge and it could be a while so I was looking to change the probe type to manual so I could still generate a mesh and use the printer. I thought I would try to compile the 2.45 firmware first but it failed. This is untouched code from this github page.

In file included from d:\vyper-vyper\marlin\src\pins\pins.h:651:0, from Marlin\src\HAL\AVR../../inc/MarlinConfig.h:34, from Marlin\src\HAL\AVR\HAL.cpp:24: d:\vyper-vyper\marlin\src\pins\stm32f1/pins_AC_TRI_F1_V1.h:25:4: error: #error "Oops! Select an STM32F1 board in 'Tools

Board.'" #error "Oops! Select an STM32F1 board in 'Tools > Board.'" ^~~~~ In file included from d:\vyper-vyper\marlin\src\pins\pins.h:651:0, from Marlin\src\HAL\AVR../../inc/MarlinConfig.h:34, from Marlin\src\HAL\AVR\HAL_SPI.cpp:34: d:\vyper-vyper\marlin\src\pins\stm32f1/pins_AC_TRI_F1_V1.h:25:4: error: #error "Oops! Select an STM32F1 board in 'Tools Board.'" #error "Oops! Select an STM32F1 board in 'Tools > Board.'" ^~~~~ In file included from d:\vyper-vyper\marlin\src\pins\pins.h:651:0, from Marlin\src\HAL\AVR../../inc/MarlinConfig.h:34, from Marlin\src\HAL\AVR\MarlinSerial.cpp:39: d:\vyper-vyper\marlin\src\pins\stm32f1/pins_AC_TRI_F1_V1.h:25:4: error: #error "Oops! Select an STM32F1 board in 'Tools

opened by midicdj1000 2
2.3.5 & 2.4.5 Auto Bed Leveling doesn't work
Auto Bed Leveling doesn't seem to work on both 2.3.5 and 2.4.5. It probes fine until the 8th probe point, then a beeping sound is made and the printer homes. At that point the screen doesn't work anymore and it needs to be restarted.

This feature works fine on the official firmware, but on this Marlin firmware it does not. The printer is stock, haven't changed anything on it.

The only change I did to the config was:

#define LIN_ADVANCE #define LIN_ADVANCE_K 0

Any idea why this is the case? Does it work for anyone else?

Best regards
opened by stuewe 2
missing firmware_release.exe tool

Hello,

I am trying to compile the code and re-write the eeprom and trying to follow the step 3 in How to flash to the mainboard, However, I cannot find the firmware_release.exe tool anythere.

Please advise.

opened by denisgosa 1
Massive Stuttering when printing via USB / UART

Description

When I print via Octoprint, there are massive stutters which lead to ugly blobs on the print. Same GCODE via SD works fine.

Additional Information

Right: blobs via Serial, left print from SD

opened by wilhelmzeuschner 1
An image is broken in the wiki
An image in the wiki is not working. Wikis don't accept PRs so I am opening an issue.

This line:

![](images/board ac_tri_f1.png)

should be like this:

![](images/board%20ac_tri_f1.png)

and it works as expected.
opened by ismailarilik 0
Minimum printing temperature

Hey guys, Hey guys and galls. Need to print PCL filament, on Vyper.

And it printing temps is 80-100. But vyper refuses to print it at that temps.

The extruder just isnt spining below 170 degrees.

How can i overcome it. Thanks.

opened by Steelman14aUA 0
Need M117 urgently - Need to display LCD messages!
Description

It is imperative that you allow showing display messages on the LCD screen so that safety messages, billing cost messages, and filament messages can be displayed from GCODE during each print.

Currently M117 is lacking. Please support this URGENTLY, thank you.

Steps to Reproduce

[First Step]

[Second Step]

[and so on...]

Expected behavior: [What you expect to happen]

M117 code on GCODE makes display show the message that is programmed in the GCODE.

Actual behavior: [What actually happens]

The firmware does not support M117 so no messages can be displayed, even a cheap Ender 3 has support for this, it's shameful that Vyper doesn't.

Additional Information

Include a ZIP file containing your Configuration.h and Configuration_adv.h files.

Provide pictures or links to videos that clearly demonstrate the issue.

See How Can I Contribute for additional guidelines.
opened by user897943 1
Update to current Marlin firmware

The last update is from 2 September. In the meantime there have been various updates from Marlin. It would be nice if there was an up-to-date firmware for the Vyper.

opened by Azathoth88 1
Inverse Extruder Motor, can't compile

I am attempting to inverse the extruder motor but cannot compile to create a stable build.

The only detail that changed is that I adjusted the extruder line 1130 of the configuration.h to be false instead of true. This is because I have a new extruder that requires the opposite directionality.

What did I do wrong? what would I need to adjust? printer is default settings for everything besides this one thing I'm trying to change

opened by whatwecee 2

Releases(vyper-v2.4.5)

vyper-v2.4.5(Sep 23, 2021)
Vyper board V2.4.5 release

Change log:

Add some abnormal popups

Add realtime temperature display when preheating and auto leveling

Add endstops abnormal popup windows when homing

Optimize the detection of power outage

How to

Download the main_board_20210902_viper_v2.4.5.rar

Extract main_board_20210902_viper_v2.4.5.rar

Copy main_board_20210902_viper_v2.4.5.bin to your sd card root directory

Power off the machine

Insert the sd card to your board sd slot

Power on the machine, wait about 1 minute until the upgrade completes

Power off the machine and eject sd card

Now your board firmware is up to date now

Source code(tar.gz)
Source code(zip)
main_board_20210902_viper_v2.4.5.rar(113.19 KB)

Owner

GitHub

MarlinRB - 3D Printer Firmware based on Marlin 3D v2.0.9.2, for Flyingbear Reborn with MKS Robin Nano v1.2, MKS Robin Nano v1.3, MKS Robin Nano S v1.3

English Прошивка MarlinRB для принтера Flyingbear Reborn Работает с платами: MKS Robin Nano v1.3 (съемные драйвера, контроллер STM32F407), MKS Robin N